I see, you get the same result with all three controllers?
Often when only one axis is not working, it can be fixed by trying one of these things:
- Make sure you don't have any other joysticks/controllers connected at the same time, that might cause a conflict.
- Make sure you uninstall vJoy and Smartpropoplus if you have them. Their driver messes with things when connecting via USB.
Keep and eye on the little circles above the OK button as you go through the Calibrate Controller procedure in Freerider. You should be able to move some of the circles smoothly up and down using the analog sticks. Sometimes the automatic stick detecting gets it wrong, in that case you can manually click on the circle that you see is the correct one (instead of clicking 'ok"). (You will still need to hold the stick fully in the direction shown for the calibration to work correctly).
Hi, from what you describe it sounds like you need to set up the endpoints on your radio.
I am not familiar with the Betafpv Literadio 2, but the issue sounds similar to what some Taranis users are experiencing (depending on what firmware version the Taranis is running).
In the case of the Taranis, the endpoints sometimes needs to be set up so that the range is from 0 to +100 (instead of -100 to +100)
It is described in this document: https://drive.google.com/file/d/0BwSDHIR7yDwSOGhPMTFyWEpDVWM/view?usp=sharing
There is also some youtube videos that shows how to do it on the Taranis, for example: https://www.youtube.com/watch?v=XlR5eqm1aKE
Also, if the automatic stick detection gets it wrong during calibration in Freerider you can manually click the circle that you see is the correct one (instead of clicking 'OK')
Hope you can use a similar method on your radio to get the calibration to work correctly!
Thanks for the fast reply. I think you are right. The range is currently - 100 to +100 (instead of 0 to 100). I have installed open tx 2.3.6 and can see those ranges in action when the sticks are moved but I can't figure out where to change the range to 0-100. Anyone have any info on this? Is that doc you sent me pictures of screen areas in open tx, or are they pics of adjustments made directly on the controller (as the Radiolite 2 does not have a screen...). Thanks again.
I found this manual for the BetaFPV Literadio 2:
However it doesn't mention anything about whether any setup adjustments is possible regarding the endpoints. My suggestion would be to contact BetaFPV directly and ask them if/how you can change the settings.
(FPV Freerider can only read what is coming in through the input manager. The input is shown as the little circles above the OK button as you go through calibration in Freerider. Ideally you should be able to move the little circles smoothly up and down between the lines on the left which marks the max/min value.)
(And yes, the pictures in the document I sent in the earlier reply is from what is seen directly on the screen of the transmitter itself, in this case a Taranis X9D).
It's a known issue with the Unity input manager and some versions of OpenTX.
Yes you are right, you need to setup the endpoints on your radio to go from 0 to +100 (instead of - 100 to +100)
You can find information on how to get your controller set up in the Taranis setup guide.
(There are also a lot of youtube videos that shows how to do it).
You can also find some general tips in the user manual.
Hi,
have a problem with a simple USB RC "Transmitter". In WIN 10 Properties i can see action when i push the sticks. But in Freerider no action when i try to calibrate. About one year ago i had no problem with this transmitter. I already tried the WIN 10 USB Driver fix. Same result. Can somebody help me further?
The input system in Freerider is the same as before, so I suspect there must be something that has changed on your system.
The automatic Windows 10 update broke the USB drivers for a lot of people, so that would be the first things that I would investigate further. I understand that you have already tried it, but I believe on some systems it might be more persistent and you might need to use a different method. Here is the method that usually works for most people (the one I guess that you have already tried).
You might want to try to search for some other methods if that didn't solve the issue on your computer. Try searching for "windows 10 usb joystick driver" on Youtube for example, here are some links: 1 2 3 4 5
Also check, just in case - that you don't have any other joysticks/controllers connected, that might cause a conflict. And, make sure you uninstall vJoy and Smartpropoplus if you have them installed. Their driver messes with things when connecting via USB.
Not sure what the mystery controller might be. I use Unity's built in input manager for the controls, I don't think it can show the name of the controller it's actually reading. Also I'm not a Mac user myself so I'm not very knowledgeable when it comes to Mac specific questions. At least on Windows joysticks/controllers that are being detected usually shoes up as a generic HID device in the operating systems device manager. Perhaps you could try to temporarily disable the last thing that you suspect might show up as a controller (although I wouldn't really recommended it if it is indeed some kind of security chip...).
My guess is it's the xbox 360 controller driver that doesn't get picked up as a joystick in Unity's input manager. Did you try to connect the controller without any extra drivers first? (A lot of the time generic gamepads automatically connects as joysticks, at least on Windows).
Hmmm that is very strange. Installing the full version shouldn't affect the demo, or vice versa.
If you have already tried all other reasonable approaches, this is what I would do:
- Delete both the demo and the full version from your computer.
- Restart your computer.
- Download the zip file for the full version again (just in case there was some error in the download)
- Unzip the full version, possible to another folder on your hard drive
- Re-connect your transmitter. Make sure you don't have any other joysticks/controllers connected at the same time as that might cause a conflict.
- Try to re-calibrate in Freerider
(As you may know there was an automatic Windows 10 update that rolled out some time ago that broke the USB drivers. I don't think that is the problem on your system though since you were using it without any problems basically just minutes before. I just thought I'd mention it anyway. You can find more information here).
I see, well I'm not a Mac user myself so I'm not very knowledgeable when it comes to MacOS specific stuff.
I would still suggest trying to start from scratch as much as possible, deleting the earlier versions and re-installing the full version.
The first thing I would do, unless you have already done so, is to simply restart the computer and see if that makes a difference.
(One more thing, you could try to go into the save game data of Freerider and see if perhaps something went wrong there. If the data somehow got messed up you might be able to get it working by deleting the old save data. The data is stored at: ~/Library/Preferences/Freerider (or something similar to that) )
Make sure you select "Joystick" as connection method when you plug in in (not "Mass storage").
What operating system are you running it on?
Do you get any movement of the little circles as you go through the Calibrate Controller procedure in Freerider?
There was an automatic Windows 10 update that rolled out some time ago that broke the USB drivers. Not sure if that affects you, but you can find more information here.
Also, there is some general tips in the user manual that you can check out.
Ok glad that you are at least able to fly using the Xbox controller. Of course it's a lot nicer to use an actual radio, so I hope you will be able to get it working. Perhaps you need to check out the Windows 10 update document (link in the above post), there are also a lot of videos on youtube videos that speaks of how some Windows 10 update broke the USB drivers (not just for Freerider) and that shows how to fix it.
Thanks for the video, judging from that it will be easy to get it working -
First of all, in the beginning it says "center all sticks", you don't need to move them - if they are already in the center just leave them be.
Second, if the automatic stick detection gets it wrong you can manually select the channel that you see is the correct one. Keep an eye on the little circles above the OK button. They show the input that is being read from the stick movement. You can manually click the little circle that you see is the correct one (instead of clicking 'OK'). (You will still need to hold the stick in the direction shown for the calibration to work correctly).
Hope that helps, let me know if you need any more info!
Generally speaking, if a controller can be recognized as a joystick by the operating system there's a good chance that it can be used with FPV Freerider.
However, I have heard reports from many people that the betafpv literadio2 does not support joystick emulation on Android. (I do believe it works in Windows though).
Since it is not recognized correctly by the operating system there is nothing I can do about it unfortunately.
