Turnigy 9xr Pro Setup on Mac el Capitan - Because it didn't exist completely anywhere else, and I am sure I will forget and need this again.

Frimware = ersky9x-pr219

Radio Setup -> Trainer 0 -> Source -> Jack, Trainer 1 -> Source -> Jack

Model -> Mixer -

1. CH1 -> Src - Thr - 100
2. CH2 -> Src - Ail - 100
3. CH3 -> Src - Ele - 100
4. Ch4 -> Src - Rud - 100

Protocol - PPM2 = On, Follow = 8CH

Module - On

1. Proto = PPM = 8CH = 300 uSec, PPM FrLen = 22.5Sec, Drive = OpenDrain, 1st Chan =1, Polarity = Neg

General - Trainer = 1

On my USB dongle it is set to G5-G7 as the others never gave me all the channels or worked properly.

Good luck and have fun, I love this program and it has helped b=me so much I cant even describe it. From noobie to pubie :)

Hi. I got the last version of FPVFreerider and it was working ok but, suddenly, doesn't matter the direction (left or right) I move my "Roll" stick, the quad only turns to one direction (Left) and I didn't do any change on the radio or on the software or even set something different...I noticed something "wrong" in the quad, then I crashed and after that never was ok again. I'm a Taranis 9xd Plus User. Thanks in advance for your help.

Hi - I have a FlySky SM600 controller on OS X and it isn't detected in FPVFreerider. Is there some magic to get this to work? Thanks!

I have an AT9 controller. When i calibrate no matter what i do both sticks will be backwards (throttle up is down on left stick, move forward is down on right stick). Instead of up on left stick for throttle and up on right stick to move forward. Do you know why that is happening?

Thanks

I'v managed to connect my DEVO 7E using Smartpropoplus and vjoy but I have now put Deviation on to the controller which supports USB connections. Looking in Windows 10 Control panel under USB game devices I can calibrate the controller and it all looks great. However when I come to play FPV freerider the calibration does not recognise the stick movements well and on the trim settings the controller sticks are all over the place (off the screen and flick to the top when the stick is moved up). Is it possible that my previous setup using Smartpropoplus have been remembered and are now interfearing with the USB setup. Is there a way to resolve this?

my taranis 9x plus only works sometimes. when i go to calibrate it doesn't do anything sometimes. when i go to check devices on windows 10 it says its connected an working fine but the game wont recognize it. sometime after closing game or restarting computer several times it will recognize it but next time i go to play it will do the same thing. i dont have any other usb devices plugged in except for keyboard and mouse. any ideas? other than that love the sim.

i have an eachine i6 controller, does it wok for this game?

I have a Devo 7 and using a USB dongle (UP02) to connect the USB to the 3.5mm socket. What am I supposed to do with the .ini file on the first page? I see no description in the manual or this thread where to put it.

Hi, I used the demo version with a logitech controller without any issues. However, now that I try to connect my Protronik PTR6A via the USB-Jack 3,5mm connector, I just get the throttle (on the second dot of the calibration page) and the pitch (on the first dot) to move. Acting on the yaw and the roll of my controller do not show anything on the screen, meaning no dots move. Something that could help solve this is hat on another simulator, the yaw was on the channel 10 and the roll on the 11th. Is there something that could help my solve my problem in the complete version ? thank you for your time. Best regards.

Hello, I just bought the dx6e of spectrum and I wish I had advice to be able to connect to Freerider. Can someone help me. Thank you all. Terry

Is there a transmitter known to work with Freerider on Android 7? I tried a few of those that I found at home, but none of them worked. The device mostly got recognized on the USB level and charging options were shown, but the HID / usbserial / whoknowswhat layer probably didn’t make it through. Some of these devices require USB mode switching (e.g. the one for my Hubsan quadcopters) and for most of them the necessary kernel modules may be simply unavailable on a default Android image. And I don’t want to root this particular phone, so I can’t dig into that too much. Is there a transmitter known to work on Android out-of-the-box? The touchscreen controls are not bad, but I miss self-centering control sticks a lot.

Just to help anyone having a problem getting controllers to work with FPVFreerider, I present my experience:

I've had a problem getting my Taranis Plus working in FPVFreerider. Basically, Windows sees the controller as a joystick device, and I can see the inputs changing the bars and so on in the Windows Joystick properties smoothly, so the controller works ok.

In FPVFreerider, the controller sticks were being seen either full off or full on, i.e. as if they were a switch. no amount of tinkering with gains of offsets helped.

However, I noticed that I also had another joystick device connected, in this case a 3DConnexion 3D Mouse, so I disabled it in device manager. Now my Taranis works flawlessly in FPVFreerider, with the controller calibration now showing the circles changing smoothly instead of either at the bottom or at the top.

I hope this helps someone else.

Hi, I'm having a bit of trouble getting my controller to work and I'm hoping for some guidance. I bought a Flysky TM912 USB controller. The game seems to recognize it, and the vertical axes on both sticks work. However, the horizontal axes are not recognized at all on the calibration page of the game. The controller works beautifully....but I can only thrust up and pitch forward and backwards...no roll or yaw. When I go to the controller settings/calibration for the device, I can see that my computer does recognize the inputs from these axes on both sticks but the game doesn't see that at all.

Hello,

First of all, thank you for this simulator. I use it on my Android smartphone.

Now I'd like to be able to use it on my PC with the transmitter of my quadcopter.

I bought a H501S from Hubsan, and I would like to know if it is possible to connect the H901A H501S-15 and if so, how to make the connection (cable and software to buy)

If not, what low-cost transmitter do you recommend?

Thanks in advance.

Thierry.

Hi

I've got Turnigy Evolution connected over USB but can't get YAW to work in fpvfreerider recharged.

Yaw works in all other sims, and is recognized in windows 10 joystick as X rotation.

The controller introduces itself to windows as HK-MT6 emulator.

Is there something I am missing?

Sry, I realy searched for a hint - but I seems to be I'm to stupid to get a flysky fs-i6 working with your simulator.

I bought this cable: http://www.banggood.com/FlySky-Data-Cable-USB-Down...

Is this wrong??

Hi there,

I have some issues with the Taranis on the mac. The Taranis both works on the FPV Freerider demo + the Recharged demo, but doesn't work on the full version of FVP Freerider itself. The stick input isn't coming through. I tried the fix from a video linked in the first post, but itjust doesn't work with the full version?!

Demo works fine but bought version crashes. Using Vista :(..... but the demo is fine.

The report window asks me to send the crash file to the developer.